Research on Low Density Cementing Technology of Coalbed Methane Well

Chufeng WANG, Ruihe WANG, Huanqiang YANG, Fangxiang WANG

Abstract


The pressure of the coalbed methane (CBM) reservoir is relatively low, there is serious loss circulation, andlow mechanical strength of the coal, which seriously influence the cementing quality. In this paper, according to the characteristics of coal in southern Qinshui basin, an ultra-low density cement slurry system and a foamed cement slurry system are designed and developed to reduce the density of cement slurry by adding lightening admixture and foaming agent through the experimental method. An appropriate bridging type preflush system is also researched and developed. Considering the drilling conditions, the operation technologies are put forward.The ultra-low density cement slurry system has good rheological performance, small API filter loss (≤ 45 mL/ (30 min·6.9 MPa)), excellent sedimentation stability, suitable thickening time and higher early strength. Foamed cement slurry systemhas good rheological performance, excellent sedimentation stability andsuitable thickening time, and can satisfy the compressive strength requirements for the cementing of CBM wells. The fluid loss of the bridging type preflush system is small under the medium or high pressure, withgood rheological performance,andexcellent plugging ability. The ultra-low density cement slurry system and foamed cement slurry system were applied in 14 and 11 CBM wells respectively, and good results have been achieved.


Keywords


Coalbed methane well; Low density cementing technology; Ultra-low density cement slurry system; Foamed cement slurry system; Bridging type preflush system

Full Text:

PDF

References


[1] Wu, J. G., Sun, M. Y., Feng, S. L., Guo, B. G., Ye, J. P., & Fan, H. (2011). Good lessons from the state -level demonstration project of coal bed methane development: An overview of such high tech and commercial project in the southern Qinshui basin. Natural Gas Industry, 31(5), 9-15.

[2] Sun, Q., Sun, J. P., Zhang, J., & Hou, Y. B. (2010). CBM geological characteristics in Shizhuang south block, southern Qinshui basin. Coal Geology of China, 22(6), 9-12.

[3] Meng, Z. P., Tian, Y. D., & Li, G. F. (2010). Characteristics of in-situ stress field in southern Qinshui basin and its research significance. Journal of China Coal Society, 35(6), 975-981.

[4] Kumar, A., & Kumar, A. (2103, November). Cementing Light & Tight: A CBM cementing story. Paper presented at the SPE Unconventional Resources Conference and Exhibition-Asia Pacific, Brisbane, Australia.

[5] Wang, C. W., & Wang, R. H. (2013, March). Using a novel spacer and ultralow density cement system to control lost circulation in coalbed methane (CBM) wells. Presented at International Petroleum Technology Conference, Beijing, China.

[6] Morris, C. W., Zanutto, S. L., & Dacres Jr, W. G. (2000, June). Lightweight cement evaluation using ultrasonic measurements. Paper presented at the SPE/AAPG Western Regional Meeting, Long Beach, California.

[7] Thomas, S. J., Smith, C., Williams, B. W., & Hamilton, L. (2014, September). Ultrasonic log response in lightweight cement conditions. Paper presented at the SPE/CSUR Unconventional Resources Conference-Canada, Calgary, Alberta.

[8] Kutchko, B., Crandall, D., Moore, J., Magdalena, G., Haljasmaa, L., Spaulding, R.,... Shine M. J. (2014, September). Assessment of foamed cement used in deep offshore wells. Paper presented at the SPE Deepwater Drilling and Completions Conference, Galveston, Texas.

[9] Sugama, T., Brothers, L. E., & Van de Putte, T. R. (2005). Air-foamed calcium aluminate phosphate cement for geothermal wells. Cement and Concrete Composites, 27(7), 758-768.

[10] Zhang, Y. H., You, L., Huang, Z., Gao, Y. K., & Yan, J. H. (2012). Experiment development of foam slurry materials. Procedia Engineering, 45, 768-773.

[11] Ding, S. D. (2002). Combination displacement cementing of turbulent and plug flow in Tahe oilfield. Oil Drilling & Production Technology, 24(1), 20-22.




DOI: http://dx.doi.org/10.3968/7581

Refbacks

  • There are currently no refbacks.


Copyright (c) 2016 Advances in Petroleum Exploration and Development




Share us to:   


Reminder

  • How to do online submission to another Journal?
  • If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

  • Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

  • Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
caooc@hotmail.com; aped@cscanada.net; aped@cscanada.org

 Articles published in Advances in Petroleum Exploration and Development are licensed under Creative Commons Attribution 4.0 (CC-BY)

ADVANCES IN PETROLEUM EXPLORATION AND DEVELOPMENT Editorial Office

Address:1020 Bouvier Street, Suite 400, Quebec City, Quebec, G2K 0K9, Canada.

Telephone: 1-514-558 6138
Website: Http://www.cscanada.net
Http://www.cscanada.org
E-mail:office@cscanada.net;  office@cscanada.org

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures